Skip to content

Checklist for Finding the Right Part When Ordering Spare Parts

Checklist for Finding the Right Part When Ordering Spare Parts

The wrong spare part prolongs downtime. A step-by-step checklist and common mistakes to help you identify the right part the first time, using machine information, the old part's label, dimensions and electrical specifications.

With spare parts, the most expensive mistake is the wrong part: a part that arrives late, does not fit and gets returned only prolongs your machine's downtime. The good news is that finding the right part usually comes down to a few key pieces of information. The checklist below helps you gather this information before placing your order.

1. Note down the machine details

The machine's brand, model, serial number and, if available, year of manufacture are shown on its nameplate. Because different hardware configurations may exist under the same model name, the serial number is very important for verifying the part.

2. Identify where the part sits on the machine

State which unit the part belongs to: clamping, injection, plasticizing, hydraulic, cooling, or the electrical and control unit. If you have the spare parts list in the machine manual or the item number in the diagram, include that as well.

3. Photograph the old part

Take clear photos of every side of the part, as well as the label, code and manufacturer markings on it. A photo showing the mounting position while the part is still installed is also useful. If the label has worn off, the part's dimensions and installation location become even more important.

4. Take the measurements

The required measurements vary by part type. The table below summarizes the information that is most often requested.

Additional information by part type
Part groupUseful information to share
Screw, barrel, nozzleScrew diameter and length, barrel inner diameter, nozzle tip size, processed raw material
Heater band, thermocoupleInner diameter, width, voltage, power, thermocouple type and length, connection type
Hydraulic seal, hose, filterInner and outer diameter, cross-section, material, working pressure, connection size
Sensor, valve, boardLabel code, signal type, output type, connector and pin layout

5. Read the electrical values

For electrical parts, voltage, power, current, signal type and connector details are essential for compatibility. Before measuring an electrical part, make sure the power is switched off and that the work is carried out by authorized personnel.

6. Write down the fault symptom and error code

Knowing why a part needs to be replaced also prevents replacing the wrong part. The error code, the message on the screen and the stage at which the fault occurred often help distinguish the real cause from the part itself.

7. State the urgency and alternatives

If the machine is down, say so clearly. If you can accept a temporary solution or an alternative part, this also makes planning easier.

Common mistakes

  • Placing an order based on appearance alone
  • Providing only the model name instead of the serial number
  • Judging dimensions without comparing the new and old parts
  • Ordering an electrical part without checking its voltage and power values
  • Throwing away the old part once the new one arrives; keep it for comparison

A sample part request

If you write your request briefly and completely, as below, the response process will be faster:

  • Machine: Brand, model and the serial number on the nameplate
  • Part: For example, the heater band in the middle zone of the barrel
  • Dimensions: Inner diameter and width
  • Electrical: Voltage, power and connection type
  • Symptom: The zone does not heat up or gives an error message
  • Urgency: Machine is down or planned replacement
  • Attachments: Photos of the part and its label

Photo-taking tips

  • Shoot the label and code area up close and in focus; avoid flash glare.
  • Include photos of the part both on its own and in its installed position.
  • For measurements, place a ruler or caliper next to the part when taking the photo.
  • Show the connection ends and connectors separately.

Equivalent parts and compatibility

A part may have equivalents from different manufacturers. If you are considering an equivalent part, clarify in advance its dimensions, material, electrical properties and compatibility with the machine manufacturer's requirements; do not install a part whose suitability you are unsure of in a safety-critical location.

Archive your part information

After each successful part replacement, keep the part's code, dimensions, photo and replacement date in the machine record. At your next request, this record both speeds up verification of the part and helps you spot recurring faults on the same machine. You can also plan your stock in advance by reviewing the records for frequently replaced parts such as heater bands, thermocouples and seals.

When you receive the part

Place the incoming part side by side with the old one and compare the dimensions, label and connections. If there is any mismatch, report it before proceeding with installation.

Send us your order

You can send the information above via our contact page. Availability, price and delivery information vary by part; we confirm this information in writing after your request. For our spare parts service, see our spare parts page, and for our part categories, see the product category.