Skip to content

8 Criteria to Consider When Choosing a Plastic Injection Molding Machine

8 Criteria to Consider When Choosing a Plastic Injection Molding Machine

Eight key criteria to consider when choosing the right injection molding machine: clamping force, shot volume, mold dimensions, plasticizing capacity, control system, energy, automation readiness, and service and spare parts support.

An injection molding machine is an investment that will run for years; the wrong tonnage, insufficient plasticizing or a platen size that does not fit the mold affects not only efficiency but also quality. The eight criteria below offer a framework for going into the conversation with the seller well prepared and for comparing your quotations soundly.

1. Clamping force (tonnage)

Clamping force is the force that prevents the mold from opening during injection. If it is insufficient, flash forms on the part; if it is greater than necessary, both the investment and the energy cost increase. The force is determined by the projected area of the part in the closing direction and the cavity pressure. For a detailed calculation example, see our tonnage calculation article.

2. Shot volume and shot weight

Shot volume is the amount of material the machine can inject in a single cycle. The total shot is found by adding the runner and the number of cavities to the part weight. In common practice, the total shot is not wanted to be either a very small fraction of the machine's capacity or very close to full capacity; a suitable range is chosen according to the material and process conditions.

3. Tie bar spacing and mold dimensions

The mold must be able to pass between the tie bars and be mounted on the platens. For this reason, the tie bar spacing, platen dimensions, minimum and maximum mold thickness and mold opening stroke must be checked against your mold. Sufficient opening distance for the part to leave the mold and for the robot to reach it should also be taken into account. For heavy molds, the platen load capacity and the ease of mold mounting (e.g. standard T-slots) are also important.

4. Plasticizing capacity

Screw diameter and length determine the amount of material that can be melted per hour and the homogeneity of the melt. The plasticizing time must remain below the cycle time. PVC, PET, engineering plastics and recycled materials may require different screw-barrel geometries; be sure to tell the seller about your raw material. Haitian states that the wear resistance of the plasticizing parts has doubled in the MARS 5 series.

5. Control system

Ease of use for the operator, screen size, recording and monitoring of process parameters, and connection options with robots and peripheral units are important. For example, in the Haitian MARS 5 series, 12.1-inch TFT LCD and 15.6-inch touchscreen options are mentioned, while in the JUPITER 5 series the "Go Factory 2.0" digital management software is mentioned as standard.

6. Energy efficiency

The drive technology (servo-hydraulic, all-electric), barrel insulation and the plasticizing system determine energy consumption. If your annual operating hours are high, even a small energy difference can change the investment decision. For a comparison, take a look at our technology comparison article.

7. Automation and robot readiness

Even if you do not need to add a robot, conveyor, in-mold labeling or camera system today, you may need to in the future. Ask whether the robot mounting surface, communication interface and safety circuits are ready; open integration possibilities reduce future cost.

8. Service and spare parts support

As much as the price of the machine, how quickly you can find support when a fault occurs is also important. Clarify in advance where and how service is provided, access to spare parts, and the documentation and operator training options. You can find our services on the technical service and spare parts pages.

Evaluate the criteria together

The eight criteria are each important individually, but they are also related to one another. For example, increasing the tonnage often brings larger platens and a larger mold area; however, shot capacity and plasticizing may not increase at the same rate. For this reason, the selection should be made not according to a single value but according to the whole combination of part, mold and target production.

Criterion and the question to ask the seller
CriterionQuestion to ask
Clamping forceWhere do I stand relative to the value calculated for my part and mold?
Shot volumeHow do the part, runner and number of cavities fit into the total shot?
Mold dimensionsDoes my mold fit between the tie bars and match the thickness and opening stroke?
PlasticizingIs there a suitable screw-barrel and hourly capacity for my raw material?
Control systemHow is process data recorded and exported?
EnergyWhat is the consumption value in a similar application?
AutomationIs the interface ready for the robot and peripheral units?
ServiceHow do I reach service and spare parts?

Common selection mistakes

  • Looking only at tonnage and not checking the mold dimensions and shot capacity
  • Selecting the machine solely for the current mold without considering future products
  • Leaving service, spare parts and training items out of the price comparison
  • Postponing automation readiness and later facing expensive retrofits

Information to prepare for the seller

  • Part dimensions, weight and raw material
  • Mold dimensions, number of cavities and runner type
  • Target cycle time and annual production volume
  • Automation and auxiliary equipment plan
  • Electrical and cooling water infrastructure

If you contact us with this information, we can carry out a preliminary assessment for the series and tonnage together. You can submit a quotation request via the contact page.